![]()
Custom Piling Machines, Factory Direct
![]()
Custom Piling Machines, Factory Direct










Crawler ground screw machine for solar piling, 4.5–6.2 t, with auger, ground screw and DTH hammer tooling.
This ground screw machine is a crawler-mounted rig for solar piling, in two sizes: the WD-4B at 4.5 t and the WD-6B at 6.2 t. The power head delivers 10–16 kN·m, and the same machine takes auger, ground screw drive head or DTH hammer tooling.
Both models are in our solar piling range, but neither one hammers piles into the ground. They drill pilot holes, screw in ground screws and drill rock.
| Model | Hole dia. / depth | Torque | Engine / power | Weight | Transport size |
|---|---|---|---|---|---|
| WD-4B | Φ150–600 mm / 4 m (auger) | 10 kN·m / 52 rpm | Weichai 4108 / 88 kW | 4.5 t | Transport 5500×2100×2800 mm; working 4000×2100×5500 mm |
| WD-6B | Φ150–750 mm / 5 m (auger) | 16 kN·m / 68 rpm | Weichai or Yuchai 6105 / 6B25; 121–130 kW | 6.2 t | Transport 5000×2300×3000 mm; working 4500×2300×5000 mm |
The WD-4B weighs 4.5 t and drills Φ150–600 mm auger holes to 4 m. The WD-6B weighs 6.2 t and drills Φ150–750 mm auger holes to 5 m. Both are crawler machines with hydraulic track drive, and power can be all-hydraulic, pure electric or hybrid. Rated depths are for the auger; actual depth depends on the auger configuration and the ground.
Both models share 400 mm track plates. Auger sizes are 95×10×4000 mm on the WD-4B and 133×12×5000 mm on the WD-6B. Ground screw drive head and DTH hammer specifications are not in the table and are available on request.
| Your job | Model to check | What decides it |
|---|---|---|
| Pilot holes Φ150–600 mm, to 4 m | WD-4B | 10 kN·m, 4.5 t, the lighter machine |
| Pilot holes Φ150–750 mm, to 5 m | WD-6B | 16 kN·m, 6.2 t, one meter more depth |
| Ground screws into soil | Either model | Drive head fitted to the ground screw you use |
| Rock, or ground screws refused by the ground | Either model | DTH hammer plus an air compressor |
Depth and hole size separate the two: 4 m and Φ600 mm on the WD-4B, 5 m and Φ750 mm on the WD-6B. Everything else is tooling. The drive head and the DTH hammer go onto the same power head, and both are specified against the ground screw or the rock you actually have. To compare other machines, browse all solar pile driving equipment.
This is a solar piling and ground screw machine. It installs foundations by drilling and turning, not by driving. That distinction decides whether it suits your site before any other number does.
For the construction side of the same job, including site checks and torque records, see our guide to the ground screw foundation.
One crawler carrier takes an auger, a ground screw drive head or a DTH hammer. The auger drills a pilot hole, the drive head screws the ground screw in, and the hammer drills rock. Tools are fitted to customer requirements.
The power head rotates whichever tool is fitted. The WD-4B head delivers 10 kN·m at 52 rpm, and the WD-6B head delivers 16 kN·m at 68 rpm, so the larger model turns tools with more force.
Hydraulic track drive moves the machine between pile positions at up to 5 km/h and climbs gradients of up to 30°. Track plates are 400 mm wide and carry the machine weight on the ground.
The mast tilts up to 30° to the left, right and forward, and the maximum lifting force is 3.8 t or more. Tilting changes the angle at which the auger or ground screw enters the ground.
Power can be all-hydraulic, pure electric or hybrid. The WD-4B lists a Weichai 4108 engine at 88 kW, and the WD-6B lists a Weichai or Yuchai engine at 121–130 kW. Electric and hybrid specifications are on request.
On this ground screw machine, the crawler carries a mast and a power head, and the tooling on the power head sets the job. With the auger, spiral flights carry soil out of the hole to make a pilot hole. With the ground screw drive head, power head torque turns the ground screw into the ground, so the soil is displaced instead of removed. With the DTH hammer, compressed air drives a hammer at the bottom of the hole that breaks rock, and an air compressor is required. The operator tilts the mast to line up each pile position.
This ground screw drill takes three kinds of tooling: an auger, a ground screw drive head and a down-the-hole (DTH) hammer. Rock and hard ground are often pre-drilled before the ground screw goes in. If you need pilot holes only, use the auger figures in the table: Φ150–600 mm to 4 m on the WD-4B or Φ150–750 mm to 5 m on the WD-6B. If you screw ground screws into hard ground or rock, send us the pile diameter, pile length and ground type, and we confirm which model can turn your ground screw or hammer before we quote.
Compressor requirements for the DTH hammer are available on request. For background on ground-mounted PV, see IEA PVPS, the International Energy Agency’s photovoltaic power systems programme. If you are unsure, send us your drawings.
Working dimensions are 4000×2100×5500 mm for the WD-4B and 4500×2300×5000 mm for the WD-6B. Transport dimensions are 5500×2100×2800 mm and 5000×2300×3000 mm. Auger drilling speed is 0.6–2.8 m/min on the WD-4B and 0.6–3.8 m/min on the WD-6B, and lifting speed is 16 m/min.
Measure the access road and the lowest bridge or overhead line on your route before you choose a machine. Transport size, not operating weight alone, often decides what can reach the site.

Power can be all-hydraulic, pure electric or hybrid, so tell us the power supply conditions at your site.
The WD-4B is the smaller model and the WD-6B is the larger one. The WD-4B weighs 4.5 t, drills Φ150–600 mm auger holes to 4 m and has a 10 kN·m power head. The WD-6B weighs 6.2 t, drills Φ150–750 mm auger holes to 5 m and has a 16 kN·m power head. Both are crawler machines.
Three tools can be fitted to this ground screw machine: an auger for pilot holes, a ground screw drive head and a DTH hammer for rock. Tools are changed to customer requirements on the same machine. Drive head and DTH hammer specifications are available on request, so send your pile diameter, pile length and ground type.
Both models can be offered with all-hydraulic, pure electric or hybrid power. Electric and hybrid specifications are available on request. Tell us the power supply conditions at your site so we can recommend the right option.
This machine is not a pile hammer. The WD-4B and WD-6B drill pilot holes, screw in ground screws and drill rock with a DTH hammer. They do not hammer piles into the ground. Tell us your pile type and ground when you inquire, and we will confirm whether the machine suits the job.
We need the pile diameter, pile length, ground type, power supply conditions and destination to recommend a machine. With those details we can tell you which model fits and which tooling to fit. Send them through the contact form or on WhatsApp.
These pages show the rest of our range: the solar pile driving equipment category where this machine is listed, and the Kaiao products center for rotary drilling rigs.
Kaiao helps you pick a model and a tooling set by ground type, pile length and power supply. Spare parts and after-sales service come from our own factory in Tengzhou, and the machines carry a one-year or 2,000-hour warranty. Learn more about Kaiao.

Tengzhou Kaiao Construction Machinery Co., Ltd. started in 2004 and has spent more than twenty years building piling equipment. Development, production, sales, after-sales service and custom work all happen in our own factory, so your questions stay with one team. The plant covers 30,000 m², employs more than 70 people, and puts every rig through four checks before shipment.
Our own factory in Tengzhou, Shandong
Development to after-sales in one team
Before every rig ships
Company-level certification, plus several patents


Send the pile diameter or ground screw size, the length, the ground type, the power supply at the site, and your destination port. If the ground is rock, say so, because that decides whether a DTH hammer and a compressor go onto the quote.
Email: [email protected]
Tel: +86 186 6320 9687
Factory: Tengfa Science and Technology Industrial Park, Shannan Road, Tengzhou City, Zaozhuang City, Shandong Province, 277500, China
Scan with WeChat. On a phone, save the image and scan it from your album.
Send us your project details and we will reply with a recommendation and a quotation.
Send an Email