Square Kelly Crawler Pile Drilling Machine, 15–30 m Depth

Crawler pile drilling machine with square kelly bar for 400–1800 mm holes to 20–25 m depth, built by Kaiao.

The WD-25 and KA-20 are pile drilling machines on crawler chassis: Φ400–1800 mm holes, 15–30 m depth, 42–55 kN·m of torque, 13–18.5 t. The KA-20 adds a telescopic chassis that narrows to 1.6 m for tight sites and widens to 2.3 m for drilling. Both use a square kelly bar.

Technical Specifications

Specification 25 m Model 20 m Telescopic Model
Model WD-25 (25 m) KA-20 Telescopic (20 m)
Chassis Crawler Crawler, telescopic
Kelly bar Square Square
Hole diameter Φ400–1800 mm (16–71 in) Φ400–1800 mm (16–71 in)
Drilling depth (rated) 25 m (82 ft) 20 m (66 ft)
Torque 55 kN·m 42 kN·m
Crowd system Cylinder Cylinder
Engine 6105 6105
Rated power 110 kW at 2200 r/min on request
Machine weight 18.5 t (40,800 lb) 13–15 t (28,700–33,100 lb)
Overall dimensions 11×2.4×3 m 10×1.6×2.9 m
Chassis width 2.4 m 1.6–2.3 m
Rotary speed (both models) 34–45 r/min
Hydraulic system pressure (both models) 16–32 MPa

Pile Drilling Machine: Which Model for Which Site

Your job Model to check What decides it
Piles to 25 m at Φ400–1800 mm, open site WD-25 55 kN·m, 18.5 t, 110 kW, 2.4 m wide
Piles to 20 m, entry narrower than 2.3 m KA-20 42 kN·m, 13–15 t, chassis 1.6–2.3 m
Piles to 20 m, but a 2.4 m entry is available WD-25 5 m more depth for 5 t more machine
Deeper than 25 m or wider than Φ1800 mm Outside this series See section 04 for the next tier

Depth is the main difference between the two: 25 m on the WD-25 against 20 m on the KA-20. Both drill the same Φ400–1800 mm range, both use a square kelly bar and a cylinder crowd system, and both run a 16–32 MPa hydraulic system at 34–45 r/min. Access width decides everything else. To compare other tiers, browse all rotary drilling rigs.

Where These Machines Fit, and Where They Do Not

These two models exist for one reason: a pile job that a standard crawler rig cannot reach. If the site is open and the piles are deep, a larger machine does the work faster and cheaper per metre.

These machines fit

  • Piles from 20 m to 25 m deep at Φ400–1800 mm, in soil and sand layers.
  • Entries between 1.6 m and 2.3 m, where the KA-20 narrows its tracks and widens them again to drill.
  • Transport at 13–18.5 t and 10–11 m long, which a standard flatbed handles.

Step to a different machine when

  • Piles run past 25 m or the ground gets harder. The 30–35 m kelly bar drill rig takes over at 120 kN·m.
  • You already run excavators on site. An excavator piling rig uses the carrier you already service.
  • Holes are wider than Φ1800 mm. Send the diameter and depth and we will say what is possible.

Both machines end up on housing, municipal, rural and power grid piles; our guide to types of piling explains how those foundations are built.

Key Features of the Pile Drilling Machine

42 and 55 kN·m, Square Bar

Both machines use a square kelly bar to pass rotary torque from the rotary head to the drilling bucket. The WD-25 delivers 55 kN·m and the KA-20 delivers 42 kN·m at a rotary speed of 34–45 r/min.

1.6 m Narrow, 2.3 m Wide

The KA-20 mini piling rig narrows its chassis to 1.6 m for transport and narrow sites, then widens it to 2.3 m for more stable drilling. Its overall size is 10×1.6×2.9 m at 13–15 t, against 11×2.4×3 m and 18.5 t for the WD-25.

Φ400–1800 mm, 20–25 m

Both machines drill Φ400–1800 mm holes. The WD-25 reaches a rated depth of 25 m and the KA-20 reaches 20 m, so depth is the main difference between them. Depths depend on the ground and the kelly bar configuration.

16–32 MPa Cylinder Crowd

A cylinder crowd system presses the bucket into the soil on both machines, on a hydraulic system of 16–32 MPa. Torque turns the bucket and crowd force pushes it down, so the two work together to fill each load.

6105 Engine, 110 kW

The WD-25 runs a 6105 engine rated at 110 kW, and you can choose the brand: Weichai, Yuchai or Cummins. The KA-20 also runs a 6105 engine.

Pile Drilling Rig: Hole Diameter, Depth and Torque

Pick by pile diameter first, then depth, then ground. The rotary head turns the drilling bucket on the square kelly bar while the cylinder crowd system presses it into the soil, and the full bucket is lifted out and unloaded before the next cycle. Both machines drill Φ400–1800 mm holes, the WD-25 to 25 m at 55 kN·m and the KA-20 to 20 m at 42 kN·m. Deeper holes, larger diameters or harder ground call for the interlocking kelly bar series to 35 m or the foundation drill rig range at 40–50 m.

Set the chassis to its wide position before the first cut on a telescopic rig. A narrow stance can let the machine rock when the bucket loads up, and the hole can drift off plumb.

For background on drilled shaft practice, see ADSC, the International Association of Foundation Drilling. If you are unsure, send us your drawings.

Mini Piling Rig for Narrow Sites: Weight and Transport Size

The KA-20 works as a mini piling rig for narrow sites. Its chassis narrows to 1.6 m for transport and tight entry, then widens to 2.3 m for more stable drilling, and its overall size is 10×1.6×2.9 m. The WD-25 measures 11×2.4×3 m. Entry also depends on turning space, ground bearing capacity and overhead clearance, so send your site limits with the enquiry.

  • KA-20: 10×1.6×2.9 m, 13–15 t, entry from 1.6 m wide.
  • WD-25: 11×2.4×3 m, 18.5 t, entry from 2.4 m wide.
  • Both fit a standard flatbed; the narrow rig also fits a container-width gate.
Kaiao rotary drilling rigs loaded for shipment to customers
Kaiao rotary drilling rig shipments to domestic and overseas customers

Frequently Asked Questions

What is the difference between the WD-25 and the KA-20?

The WD-25 drills to 25 m with 55 kN·m and weighs 18.5 t, while the KA-20 drills to 20 m with 42 kN·m and weighs 13–15 t. The KA-20 also has a telescopic chassis that adjusts from 1.6 to 2.3 m, which helps on narrow sites.

What hole diameter can this pile drilling machine drill?

Both machines drill Φ400–1800 mm holes (16–71 in) in diameter. The WD-25 drills to a rated depth of 25 m and the KA-20 to 20 m. Depths are rated values and depend on the ground and the kelly bar configuration.

Which engine does the WD-25 use?

The WD-25 uses a 6105 engine rated at 110 kW at 2200 r/min, and you can choose the brand: Weichai, Yuchai or Cummins. Tell us your preferred brand when you request a quote and we will confirm the configuration.

Can I get a machine for deeper piles?

Kaiao builds crawler interlocking kelly bar rigs that reach 30–35 m, and foundation drill rigs for 40–50 m. Send us your pile diameter, depth and ground conditions, and we will tell you honestly which machine fits your project.

What rotary head torque do these machines deliver?

The WD-25 delivers 55 kN·m and the KA-20 delivers 42 kN·m, both at a rotary speed of 34–45 r/min. Both values are rated rotary head torque, and a cylinder crowd system presses the bucket into the soil.

What are the chassis width and weight of each machine?

The KA-20 has a telescopic chassis that adjusts from 1.6 to 2.3 m and an overall size of 10×1.6×2.9 m at 13–15 t (28,700–33,100 lb). The WD-25 measures 11×2.4×3 m overall and weighs 18.5 t (40,800 lb).

What warranty covers these machines?

These machines carry a one-year warranty or 2,000 operating hours; the exact terms are confirmed in your order. Kaiao supplies spare parts and after-sales service from its own factory.

What overhead clearance do these machines need?

Overall height is 2.9 m on the KA-20 and 3 m on the WD-25, and that is the machine dimension, not the working height with the mast raised. If your site has an overhead limit, send it with your quote request and we will confirm the working height of the machine you need.

Related Applications

  • Housing project foundations
  • Municipal construction piles
  • Rural building foundations
  • Power grid upgrade foundations

Technical Support

Kaiao helps you pick a machine by pile diameter, depth and site access. Spare parts and after-sales service come from our own factory in Tengzhou, and the machines carry a one-year or 2,000-hour warranty. Learn more about Kaiao.

Overseas customers visiting the Kaiao factory in Tengzhou
Group photos of overseas customers at the Kaiao factory

Factory and Custom Work

Tengzhou Kaiao Construction Machinery Co., Ltd. handles development, production, sales, after-sales service and custom work in its own factory, so your questions stay with one team. The plant covers 30,000 m², employs more than 70 people, and puts every rig through four checks before shipment.

30,000 m² Plant

Our own factory in Tengzhou, Shandong

70+ Employees

Development to after-sales in one team

4 Checks

Before every rig ships

ISO 9001 and CE

Company-level certification, plus several patents

Kaiao factory overview and production workshop in Tengzhou
Welding, machining and assembly at the Kaiao factory
Kaiao ISO 9001 and CE certificates
Kaiao patent certificates

Request a Quote for the Mini Piling Rig

Send the deepest pile, the hole diameter, the narrowest gate or lane the machine has to pass, measured in metres, the ground or soil report, and your destination port. If that entry is under 2.3 m, say so first, because it decides between the two models before anything else does.

Contact Kaiao

Email: [email protected]

Tel: +86 186 6320 9687

Factory: Tengfa Science and Technology Industrial Park, Shannan Road, Tengzhou City, Zaozhuang City, Shandong Province, 277500, China




Need a quote? Chat with us