Large Crawler Foundation Drill Rig, 40–50 m Depth

Large crawler foundation drill rig for Φ1800 mm holes to 40 m or 50 m depth, built in Tengzhou by Kaiao.

This large crawler foundation drill rig drills Φ1800 mm holes to 40 m or 50 m depth with 150–170 kN·m of torque. Built as a foundation drilling rig for large piles, it weighs 42–50 t and runs a 194 kW Cummins engine. Both versions are built in our own factory in Tengzhou, Shandong.

Technical Specifications

Specification 40 m Version 50 m Version
Model KA-155 (40 m, Telescopic) KA-155 (50 m)
Chassis Crawler, telescopic undercarriage Crawler
Hole diameter Φ1800 mm (71 in) Φ1800 mm (71 in)
Drilling depth (rated) 40 m (131 ft) 50 m (164 ft)
Torque / rotary speed 150 kN·m / 8–40 r/min 170 kN·m / 7–33 r/min
Crowd force / stroke 140 kN / 3200 mm 155 kN / 3500 mm
Main winch line pull 150 kN 160 kN
Engine Cummins 260 hp Cummins 260 hp
Rated power 194 kW 194 kW
Machine weight 42 t (92,600 lb) 50 t (110,200 lb)
Travel speed 3 km/h 3 km/h
Transport dimensions 13500×3000×3500 mm 13000×3200×3500 mm
Track gauge 3000–4200 mm 3200–4400 mm
Gradeability 35% 35%
Hydraulic system pressure 35 MPa 35 MPa
Mast inclination ±5° / 5° / 15° ±5° / 5° / 15°

Foundation Drill Rig: 40 m and 50 m Models Compared

Comparison item 40 m version 50 m version
Drilling depth / hole diameter 40 m / Φ1800 mm 50 m / Φ1800 mm
Torque / rotary speed 150 kN·m / 8–40 r/min 170 kN·m / 7–33 r/min
Crowd force / stroke 140 kN / 3200 mm 155 kN / 3500 mm
Main winch line pull 150 kN 160 kN
Machine weight 42 t 50 t
Transport dimensions 13500×3000×3500 mm 13000×3200×3500 mm
Track gauge 3000–4200 mm, telescopic 3200–4400 mm
Your project Better fit Why
Piles up to 40 m, limited site or road access 40 m version 42 t machine weight against 50 t, and a 3000 mm transport width
Piles up to 50 m, wide site access 50 m version 170 kN·m of torque and 160 kN of winch line pull for a deeper hole
Holes over Φ1800 mm or deeper than 50 m Heavy-duty crawler series Holes 57–105 m deep and up to Φ2700 mm in diameter
Small piles or very narrow access roads Compact crawler rotary rig A smaller, lighter machine for tight access

Both versions share the Φ1800 mm hole diameter, the Cummins 194 kW engine and the 35 MPa hydraulic system. The 50 m version adds depth, torque, crowd force and winch pull, at a cost of 8 t of machine weight and 200 mm of transport width. Pick the version by pile depth first, then check site access. To compare other tiers, browse all rotary drilling rigs.

Where This Rig Fits, and Where It Does Not

Both versions are built for one job: boring Φ1800 mm cast-in-place pile holes to 40 m or 50 m. If your pile falls outside that window, a different machine in the range does the work better, and saying so saves both sides a site visit.

This rig fits

  • Bored piles at Φ1800 mm, 40 m or 50 m deep, in soil a drilling bucket can cut.
  • Sites that can take a 42–50 t machine and a transport length of 13 to 13.5 m.
  • Pile layouts that need the tracks narrowed: 3000–4200 mm gauge on the 40 m version.

This rig is not the right machine for

  • Holes wider than Φ1800 mm. Our caisson drill rig series covers Φ2000–2700 mm.
  • Depths beyond 50 m. The same series reaches 105 m.
  • Access roads or gates narrower than the shipping width, or bridges rated under 50 t.
  • Small piles behind a narrow entrance. A 15–35 m kelly bar drill rig moves in where this one cannot.
  • A foundation that mixes small CFA piles into the large rotary piles. The CFA piling rig pours Φ600–800 mm piles in one pass, then switches to rotary tooling for the larger ones.

Bored piles are one of several pile types used on building sites; our guide to types of piling sets out how they differ from driven and screw piles.

Key Features of the Foundation Drill Rig

150 kN·m at 8–40 r/min

The rotary head delivers 150 kN·m at 8–40 r/min on the 40 m version and 170 kN·m at 7–33 r/min on the 50 m version. That torque spins the drilling bucket through the soil, so each cycle fills the bucket before the winch lifts it out.

140 kN Crowd, 3200 mm Stroke

A cylinder crowd system presses the drilling bucket into the soil with 140 kN over a 3200 mm stroke on the 40 m version, and 155 kN over 3500 mm on the 50 m version. The deeper rig gets more push and more travel per stroke.

3000–4200 mm Telescopic Gauge

The 40 m version runs a telescopic undercarriage with a 3000–4200 mm track gauge at 42 t. The 50 m version runs a 3200–4400 mm track gauge at 50 t. Both travel at 3 km/h and climb 35% gradients, so the tracks move the rig around the site under its own power.

Cummins 260 hp, 35 MPa

Both versions use a Cummins 260 hp (194 kW) engine and a 35 MPa hydraulic system. One power package feeds the rotary head, crowd cylinder, winches and travel.

150 kN Winch, ±5° Mast

The main winch pulls 150 kN on the 40 m version and 160 kN on the 50 m version to lift the loaded bucket out of the hole. The mast inclination of ±5° / 5° / 15° lets the operator set the mast plumb over the pile position.

Foundation Drilling Rig for Large Piles: Torque and Hole Diameter

A foundation drilling rig has to turn the tool, press it down and lift it out, so torque is only one number to check. The rotary head turns the drilling bucket on the kelly bar while the crowd cylinder presses it into the soil. The main winch then lifts the full bucket out, and the bucket swings over to unload.

Check the mast plumb before the first cut and again after the bucket passes the upper layer. A mast that leans early lets the hole drift, and the error grows with depth.

The rig drills the hole; the pour that follows has its own rules, covered in our guide to the tremie pipe. For background on drilled shaft practice, see ADSC, the International Association of Foundation Drilling. If you are unsure, send us your drawings.

Foundation Drill Rigs for Sale: Weight and Transport Size

Plan transport before you commit, because the two versions ship at different sizes. The 40 m version ships at 13500×3000×3500 mm and 42 t. The 50 m version ships at 13000×3200×3500 mm and 50 t. Tell us your destination and site conditions and we will confirm whether the size fits your route.

  • The 40 m version narrows to a 3000 mm transport width, which suits a standard low-bed trailer.
  • The 50 m version adds 200 mm of width and 8 t of weight for the extra 10 m of depth.
  • Both ships at 3500 mm high, so check the lowest bridge or overhead line on the route.
Kaiao rotary drilling rigs loaded for shipment to customers
Kaiao rotary drilling rig shipments to domestic and overseas customers

Frequently Asked Questions

What depth can this foundation drill rig reach?

The 40 m version drills to a rated depth of 40 m (131 ft) and the 50 m version to 50 m (164 ft), and both drill holes up to Φ1800 mm (71 in) in diameter. The reachable depth on your site depends on the kelly bar configuration and the ground conditions.

Which engine does it use?

Both versions run a Cummins 260 hp (194 kW) engine paired with a 35 MPa hydraulic system. That power package feeds the rotary head, crowd cylinder, winches and travel on the 40 m version and on the 50 m version.

Do you have a rig for deeper or larger holes?

Kaiao offers a heavy-duty crawler series for holes 57–105 m deep and up to Φ2700 mm in diameter. Send us your pile diameter, depth and ground conditions, and we will tell you honestly which machine fits your project.

How do I get a quote?

Send Kaiao your pile diameter, drilling depth, ground conditions and destination through the contact form or on WhatsApp. We review the details, recommend the version that fits and answer any questions about machine size or weight. We reply within 24 hours.

How is this rig transported between job sites?

The 40 m version ships at 13500×3000×3500 mm and 42 t (92,600 lb), and the 50 m version ships at 13000×3200×3500 mm and 50 t (110,200 lb). Tell Kaiao your destination and site access, and we will confirm whether these sizes fit your route.

What torque, crowd force and winch pull does this model offer?

The 40 m version offers 150 kN·m of torque, 140 kN of crowd force and 150 kN of main winch line pull. The 50 m version offers 170 kN·m, 155 kN and 160 kN. Hole diameter is Φ1800 mm on both versions.

What warranty does this rig carry?

This rig carries a one-year warranty or 2,000 operating hours; the exact terms are confirmed in your order. Kaiao also supplies spare parts and after-sales service from its own factory in Tengzhou.

Related Applications

  • Large-diameter bored piles
  • Deep cast-in-place pile foundations
  • Bridge and heavy structure foundations
  • High-rise building foundations

Technical Support

Kaiao helps you choose between the two versions by pile diameter, depth and ground conditions. Spare parts and after-sales service come from our own factory in Tengzhou, and the rig carries a one-year or 2,000-hour warranty. Learn more about Kaiao.

Overseas customers visiting the Kaiao factory in Tengzhou
Group photos of overseas customers at the Kaiao factory

Factory and Custom Work

Tengzhou Kaiao Construction Machinery Co., Ltd. handles development, production, sales, after-sales service and custom work in its own factory, so your questions stay with one team. The plant covers 30,000 m², employs more than 70 people, and puts every rig through four checks before shipment.

30,000 m² Plant

Our own factory in Tengzhou, Shandong

70+ Employees

Development to after-sales in one team

4 Checks

Before every rig ships

ISO 9001 and CE

Company-level certification, plus several patents

Kaiao factory overview and production workshop in Tengzhou
Welding, machining and assembly at the Kaiao factory
Kaiao ISO 9001 and CE certificates
Kaiao patent certificates

Request a Quote for the Foundation Drilling Rig

Send the deepest pile on the job, the hole diameter, the ground or soil report, the narrowest point on your access road, and your destination port. If you are still choosing between the 40 m and the 50 m version, say so, and we will tell you which one the site actually needs.

Contact Kaiao

Email: [email protected]

Tel: +86 186 6320 9687

Factory: Tengfa Science and Technology Industrial Park, Shannan Road, Tengzhou City, Zaozhuang City, Shandong Province, 277500, China




Need a quote? Chat with us